Coolpad Surf - CP331A

Hotspots and Dongles related Topics
User avatar
Didneywhorl
Posts: 1172
Joined: Fri Mar 23, 2018 5:37 pm
Location: USA
Has thanked: 321 times
Been thanked: 192 times
Contact:

Re: Coolpad Surf - CP331A

Post by Didneywhorl » Mon Jun 22, 2020 8:21 pm

Give it a go! Usually the amplifiers seem to work best with very narrow spectrums of frequency. Sounds like you got a project! :)
The Solution for your Internet Connectivity and Speed.

Whitt
Posts: 2
Joined: Mon Jun 22, 2020 3:02 pm
Has thanked: 0
Been thanked: 0

Re: Coolpad Surf - CP331A

Post by Whitt » Thu Jun 25, 2020 12:35 am

I'm already in the middle of another (unrelated) project, but as soon as it wraps up, I need to get a more reliable signal.

Amp Frequencies: BANDS 04, 05, 13, 17, 25/2

(Up/Down):

698 - 716 MHz / 728 - 746 MHz, 776 - 787 MHz / 746 - 757 MHz, 824 - 849 MHz / 869 - 894 MHz, 1710 - 1755 MHz / 2110 - 2155 MHz, 1850 - 1915 MHz / 1930 - 1995 MHz

Also, the amp is bidirectional, so it amplifies the signal both ways.

parkskier426
Posts: 1
Joined: Wed Jul 15, 2020 6:02 pm
Has thanked: 0
Been thanked: 0

Re: Coolpad Surf - CP331A

Post by parkskier426 » Wed Jul 15, 2020 6:28 pm

So I wanted to try out an external antenna on this thing but based on previously posted pictures, I was pretty sure that this doesn't have an MHF4 connector. After a lot of digging, here's what I've come up with:
  • This type of connector is commonly used during the manufactoring process to measure signal levels to reject bad boards.
  • What's not clear is if this cable would work with this RF switch. Also, I can't find it anywhere for purchase, and it may cost more than it's worth for this project.
What I did notice is that there are two places where the antennas in the caseing is connected to the board, presumably one for wifi, the other for cellular. It should be easy to solder at these points to add on antenna. This is where I'm stuck. There appear to be 3 contact points for the antennas, and I'm not sure what each are. If anyone has expirience here and could shed some light, it would be helpful. I've attached images of the connection points from the board, the case, and what I belive to be the antennas.
MVIMG_20200715_171238.jpg
MVIMG_20200715_171221.jpg
MVIMG_20200715_171431.jpg

shoulin333
Posts: 26
Joined: Wed Mar 04, 2020 1:15 am
Has thanked: 1 time
Been thanked: 5 times

Re: Coolpad Surf - CP331A

Post by shoulin333 » Fri Jul 31, 2020 12:52 pm

I have one of these on the way to see if it works. It should plug on to the "testing port" and allow for external antenna.


https://www.ebay.com/itm/RG174-SMA-FEMA ... 2749.l2649

shoulin333
Posts: 26
Joined: Wed Mar 04, 2020 1:15 am
Has thanked: 1 time
Been thanked: 5 times

Re: Coolpad Surf - CP331A

Post by shoulin333 » Thu Aug 06, 2020 2:01 pm

Update: The pigtail didn't work. The connector is smaller than MS-156. Holding off on digging any deeper right now.

jedihustle
Posts: 1
Joined: Sun Oct 18, 2020 1:31 pm
Has thanked: 0
Been thanked: 0

Re: Coolpad Surf - CP331A

Post by jedihustle » Sun Oct 18, 2020 1:36 pm

grant11 wrote:
Sun Apr 26, 2020 11:37 pm
Another thing is I've got it setup for my grandmother who is an hour away but I've got a problem where it will freeze up after a few days. It's connected to an asus router that supports the tether in the stock firmware.
What Asus router do you recommend me buying for this device? Does that setup allow for you to get around the 13 device limit? Have you been able to figure out how to have it reboot automatically?

Post Reply